Skills integration

Topics: Network switch, IP address, Spanning tree protocol Pages: 6 (422 words) Published: February 9, 2014
Packet Tracer – Skills Integration Challenge
Topology

Addressing Table
Device
Interface
IP Address
Subnet Mask
Default Gateway
VLAN Association
R1
G0/0.1
192.168.99.1
255.255.255.0
N/A
VLAN 99

G0/0.10
192.168.10.1
255.255.255.0
N/A
VLAN 10

G0/0.20
192.168.20.1
255.255.255.0
N/A
VLAN 20

S0/0/0
209.165.22.222
255.255.255.224
N/A
N/A

S0/0/1
192.168.1.1
255.255.255.0
N/A
N/A
R2
G0/0.1
192.168.99.2
255.255.255.0
N/A
VLAN 99

G0/0.10
192.168.10.2
255.255.255.0
N/A
VLAN 10

G0/0.20
192.168.20.2
255.255.255.0
N/A
VLAN 20

S0/0/0
192.168.1.2
255.255.255.0
N/A
N/A

S0/0/1
209.165.22.190
255.255.255.224
N/A
N/A
ISP
S0/0/0
209.165.22.193
255.255.255.224
N/A
N/A

S0/0/1
209.165.22.161
255.255.255.224
N/A
N/A
Web
NIC
64.104.13.130
255.255.255.252
64.104.13.129
N/A
PC10A
NIC
192.168.10.101
255.255.255.0
192.168.10.1
VLAN 10
PC10B
NIC
192.168.10.102
255.255.255.0
192.168.10.1
VLAN 10
PC20A
NIC
192.168.20.101
255.255.255.0
192.168.20.1
VLAN 20
PC20B
NIC
192.168.20.102
255.255.255.0
192.168.20.1
VLAN 20
Scenario
In this activity, two routers are configured to communicate with each other. You are responsible for configuring subinterfaces to communicate with the switches. You will configure VLANs, trunking, and EtherChannel with PVST. The Internet devices are all preconfigured. Requirements

You are responsible for configuring routers R1 and R2 and switches S1, S2, S3, and S4. Note: Packet Tracer does not allow assigning point values less than 1. Since this activity is checking 154 items, not all configurations are assigned a point value. Click Check Results > Assessment Items to verify you correctly configured all 154 items. Inter-VLAN Routing

On R1 and R2, enable and configure the subinterfaces with the following requirement: Configure the appropriate dot1Q encapsulation.
Configure VLAN 99 as the native VLAN.
Configure the IP address for the subinterface according to the Addressing Table.

Routing
Configure OSPFv2 using the following requirements:
User process ID 1.
Advertise the network for each subinterface.
Disable OSPF updates for each subinterface.
VLANs
For all switches, create VLAN 10, 20, and 99.
Configure the following static ports for S1 and S2:
F0/1 – 9 as access ports in VLAN 10.
F0/10 – 19 as access ports in VLAN 20.
F0/20 – F24 and G1/1 – 1/2 as the native trunk for VLAN 99. Configure the following static ports for S3 and S4:
F0/1 – 9 as access ports in VLAN 10.
F0/10 – 20 as access ports in VLAN 20.
F0/21 – F24 and G1/1 – 1/2 as the native trunk for VLAN 99. EtherChannels
All EtherChannels are configured as LACP.
All EtherChannels are statically configured as the native trunk for VLAN 99. Use the following table to configure the appropriate switch ports to form EtherChannels: Port Channel
Device: Ports
Device: Ports
1
S1: G1/1 – 2
S3: G1/1 – 2
2
S2: G1/1 – 2
S4: G1/1 – 2
3
S1: F0/23 – 24
S2: F0/23 – 24
4
S3: F0/23 – 24
S4: F0/23 – 24
5
S1: F0/21 – 22
S4: F0/21 – 22
6
S2: F0/21 – 22
S3: F0/21 - 22
Spanning Tree
Configure per-VLAN rapid spanning tree mode for all switches. Configure spanning tree priorities according to the table below: Device
VLAN 10 Priority
VLAN 20 Priority
S1
4096
8192
S2
8192
4096
S3
32768
32768
S4
32768
32768

Connectivity
All PCs should be able to ping the Web and other PCs.
Continue Reading

Please join StudyMode to read the full document

You May Also Find These Documents Helpful

  • Teamwork Skills Research Paper
  • Essay on Managerment skill
  • Learning Skill Essay
  • Criticalthink Skills Essay
  • Learning and Skill Essay
  • Leadership Skills Essay
  • Organisational Skills Essay
  • Skills Matrix Essay

Become a StudyMode Member

Sign Up - It's Free